BVP80 - Ball Valves, Pneumatic and Electric Actuated Models

Mô tả:
Nhà phân phối Omega tại Việt Nam
Chia sẻ:
Số lượng
số điện thoại

Ball Valves, Pneumatic and Electric Actuated Models

 

 

SPECIFICATIONS
BVE80 and BVE70 Series
Materials of Construction
Enclosure: FR50 Cover, PTFE coated cast aluminum base
Shaft: 18-8 Stainless Steel
External Trim: 300 Series Stainless Steel
Temperature: 4.4 to 65.5°C (40 F to 150°F)
Motor: Reversing, brushless, capacitor-run with auto-reset thermal overload protection
Gear Train: Permanently lubricated, maintenance free
Power: 120 Vac 50-60 Hz single phase
Ports: (2) ½ NPT conduit
Cycle Time: 6 sec
Duty Cycle: 
   Models <25 mm (1"): 100%,
   Models ≥32 mm (1-0,25"): 75%
Torque Output:
   Models <25 mm (1"): 150 in-lbs 
   Models ≥32 mm (1-0,25"): 300 in-lbs 

BVP-BVPS80 and BVP-BVPS70 Series
Materials of Construction
Body: Aluminum with PTFE impregnated hard anodized surfaces
External Hardware: (pinion shaft, driver, end caps) 300 Series Stainless Steel
Spring Modules: Nylon resin housing or manufactured Aluminum, 300 SS hardware External Trim: 300 Series Stainless Steel
Temperature: -28.8 to 176.6°C (-20 to 350°F)
Power: 3.4 to 8.6 bar (50 to 125 psi) air. Sufficient air delivery must be available at the actuator to ensure dependable operation. The following precautions should be observed: Air supply should be clean and free of moisture. When dirty or wet air is a problem; a filter-separator should be specified; these units are most effective when installed as closely as possible to the actuator. A filter, when used, should permit a minimum flow of 4 scfm at an upstream pressure of 4 bar (60 psi). Eliminate severe restrictions to air flow (certain solenoid valves and fittings). The most restricted passage must have an area no smaller than 0.012 in2, the area of 3 mm (1-8") diameter orifice. If more than a single actuator is to be supplied by an individual pilot, the minimum passage requirement applies per actuator.
Port Connections: 1-8 NPT
Tubing: For short runs up to 1.5 m (5), 4 mm (5-32") I.D. is suitable, 6 mm (1-4") I.D. will serve up to 9 m (30). For longer runs, use 10 mm (3-8") I.D. or larger.
Interface: NAMUR
Duty Cycle: 100%
Cycle Time: (To open or close) approx 1-2 to 1 second (dependent upon actuator model, air pressure and delivery)

 

BVP80 - Ball Valves, Pneumatic and Electric Actuated Models

Bình luận của bạn
*
*
 Captcha
Danh mục hãng cung cấpDanh mục hãng cung cấp
Hỗ trợ trực tuyến
Liên hệ tư vấn mua hàng
Thống kê truy cập
  • Trực tuyến:
    4
  • Hôm nay:
    267
  • Tuần này:
    6388
  • Tháng trước:
    16566
  • Tất cả:
    612140
CÔNG TY TNHH THƯƠNG MẠI VÀ DỊCH VỤ TĂNG MINH PHÁT

 VPĐD: Số 01, đường số 27, phường Hiệp Bình Chánh, Quận Thủ Đức, Tp.HCM

 Ðiện Thoại:  (028) 35121007                Fax: (028) 35121008

 Nhân viên kinh doanh: Sĩ Nguyên (Mr.)

 Email:  Sale08@tmpvietnam.com        Tel: 091 7543068

 VP tại Đức: Am Boscheler Berg 4a 52134 Herzogenrath

 Website: avantgarde-x.de

Hình Thức Thanh Toán
Bản Đồ

© 2017 Tangminhphat.com, all right reserved.

Thiết kế website www.webso.vn

Loading...

Back To Top